肯德基门实质上是铝合金门，商业区的肯德基、麦当劳等大多数快餐店都是用的肯德基门。和传统的玻璃门、钢质门、卷帘门相比，肯德基门采光度更好，色泽持久鲜艳。最关键是肯德基门更具有使用性。肯德基门的实用性不仅受其本身质量的影响，跟安装也有关系。

Kendl Ki Men is essentially an aluminum alloy door, and most of the fast food restaurants in KFC and McDonald's are KFC doors. Compared with traditional glass door, steel door and rolling door, KFC door has better color and bright color. The key is that Kentucky gate is more useful. Kendl Ki Men's practicality is not only affected by its own quality, but also related to installation.

那安装肯德基门的步骤是怎样的呢?肯德基门制作有其特点，所以安装由有其特点。那么，安装的过程中又有哪些是需要注意的呢？

What is the procedure of installing KFC? The production of KFC door has its own characteristics, so installation has its own characteristics. Then, what are the need to pay attention to during the installation process?

第一步：清理门洞，剔除多余部分，保证门洞两侧都在垂直线上；

The first step: clean the door, remove the redundant part, which are openings on both sides of the vertical line;

第二步：安装门框上的顶轴部分；

Second step: install the top axle part on the door frame;

第三步：用螺丝或铆钉组合门框的三根型材；

The third step is to use screws or rivets to form three sections of the doorframe.

第四步：安装地轴，在地上开出长170mm宽120mm深度为55mm的方形坑。浇注砂浆，固定地轴的时候从顶轴的中心用线锤垂直至地轴轴承的中心固定好地轴、水泥干燥后进行下一步。

The fourth step: install the earth axis, and open the rectangular pits with 170mm long 120mm and 55mm depth on the ground. When pouring the mortar and fixing the earth axis, the center of the bearing is perpendicular to the center of the axle, and the center of the bearing is fixed well, and the cement is dried for the next step.

第五步：安装门体的上轴和下轴；

The fifth step is to install the upper and lower shaft of the door.

第六步：安装门前需要注意的两点；

The sixth step: two points needing attention before the installation of the door;

1、松开门扇上的防盗卡位螺丝；

The anti-theft fastener screw 1, loosen the door leaf;

2、装门扇前在地轴上抹润滑黄油使门扇开合自如增加使用寿命。

2, before the leaf is arranged on the lubricating grease makes the door open free to increase the service life.

第七步：按上个步骤安装另外门扇；

Seventh step: install another fan according to the previous step.

第八步：

The eighth step:

1、调试门扇位置的方法，松开盖板可以用扳手调节地轴的螺丝；

1, debug the location of door leaf, release the cover plate, and use the wrench to adjust the screw of the ground axis.

2、调试门扇上下方法，具体方法是调试下轴上的六棱螺丝顺时针调试

2, debug the door leaf up and down method. The specific method is to debug the six edge screws on the lower shaft, clockwise debugging.

门扇向上，逆时针调试门扇向下；

The door fan is upwards, and the door fan is debugged against clockwise.

第九步：紧劳防盗卡位螺丝；

The ninth step: tight labor card anti-theft screws;

第十步：安装闭门器，安装方法见闭门器配套安装说明书。调试闭门器开关门速度，安装完毕。

The tenth step: install the door closer, and see the installation instructions for the door closer. The debug door Shuter opens the shutting speed, and the installation is finished.