肯德基门，行业术语，主要适用于酒店、商场、办公楼、银行、咖啡厅、展示厅和快餐店 等场所， 内门、外门均可安装使用。可有效起到隔温、防尘、防沙、降噪隔音、遮蔽等作用。

Kentucky gate, industrial terminology, mainly applicable to hotels, shopping malls, office buildings, banks, cafes, exhibition halls and fast food shops, such as places, the inner door, the outside door can be installed and used. It can effectively play the role of temperature isolation, dust prevention, sand prevention, noise reduction, noise insulation and shelter.

肯德基门，实质上就是实质上是铝合金门。肯德基门采光度好，色泽持久鲜艳。

The KFC door is essentially an aluminum alloy door. Kendl Ki Men has a good light and a long and bright color.

肯德基门主要由门框、门扇、门体玻璃、大拉手、大铰链、闭门器等组成。该门型均可安装于室内和室外。每樘门有两个门扇，左门扇、右门扇。门扇厚度40-60mm。 门扇一边的边框与门框之间由大铰链连接，门扇另一边门边框上安装有扳动式上下插销，门扇顶部横梁一侧安装有闭门器与门框连接，门体大铰链采用底部螺栓旋紧方式。门扇中间部分可增加横撑，美观的同时也方便行人出入。

Kendl Ki Men is mainly composed of doorframe, door leaf, door glass, big handle, large hinge, door closer and so on. The door type can be installed indoors and outdoors. Each door has two doors, left door and right door fans. The thickness of the door fan is 40-60mm. The side frame of the door fan is connected by a large hinge between the frame and the door frame. The door frame is mounted on the other side of the door. The door side is connected with the door frame on one side of the top beam of the door fan, and the large hinge of the door body adopts the bottom bolt tightening method. The middle part of the door leaf can be added with horizontal braces, which is also convenient for pedestrians to enter and leave.

肯德基门的安装方法

The installation method of Kendl Ki Men

肯德基门制作有其特点，所以安装时候也和普通门窗的安装有所不同。那么，肯德基门安装的步骤是什么呢？

KFC door making has its own characteristics, so the installation time is different from the installation of ordinary doors and windows. So, what is the installation procedure of Kendl Ki Men?

      

      

       第一步：清理门洞，剔除多余部分，保证门洞两侧都在垂直线上；

The first step is to clean up the door, eliminate the unnecessary parts, and ensure that both sides of the door are on the vertical line.

       第二步：安装门框上的顶轴部分；

The second step: install the top axle part of the doorframe.

       第三步：用螺丝或铆钉组合门框的三根型材；

The third step is to use the screws or rivets to form the three sections of the doorframe.

       第四步：安装地轴，在地上开出合适长宽和纵深的方形坑。浇注砂浆，固定地轴的时候从顶轴的中心用线锤垂直至地轴轴承的中心固定好地轴、水泥干燥后进行下一步。

The fourth step: install the earth shaft, and open the square pit with suitable length width and depth on the ground. When the mortar is fixed, the center of the bearing is fixed vertically from the center of the top shaft to the center of the bearing, and the next step is to dry the cement.

      第五步：安装门体的上轴和下轴；

The fifth step: install the upper and lower axle of the door body.

      第六步：安装门前需要注意的两点；

Sixth steps: two points to be noted before installing the door;

      1、松开门扇上的防盗卡位螺丝；

1, loosen the anti-theft card screw on the door leaf.

      2、装门扇前在地轴上抹润滑黄油使门扇开合自如增加使用寿命。

2, install grease on the floor before installing the door leaf to make the door open and fit and increase the service life.

      第七步：按上个步骤安装另外门扇；

The seventh step: install the other door leaf according to the previous step.

第八步：

The eighth step:

1、调试门扇位置的方法，松开盖板可以用扳手调节地轴的螺丝；

1. Adjust the position of the door leaf. Release the cover plate and use the wrench to adjust the screw of the ground shaft.

2、调试门扇上下方法，具体方法是调试下轴上的六棱螺丝顺时针调试门扇向上，逆时针调试门扇向下；

2, debug the door leaf up and down method, the specific method is to debug the six edge screw on the lower shaft, adjust the door leaf clockwise upward, and adjust the door leaf downward counter clockwise.

第九步：紧劳防盗卡位螺丝；

The ninth step: tighten the burglar security card screw;

第十步：安装闭门器，安装方法见闭门器配套安装说明书。调试闭门器开关门速度，安装完毕。

The tenth step: installation of door closer, installation methods see the door closer supporting installation instructions. The debug door Shuter opens the shutting speed, and the installation is finished.